1 1/2" 3 Way Corner Pipe Connector
thingiverse
Customized version of https://www.thingiverse.com/thing:2958009 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2958009
1 1/2" 3 Way Corner Pipe Connector (Thinner Wall)
thingiverse
Customized version of https://www.thingiverse.com/thing:2958009 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2958009
3 Way Corner Pipe Connector (For 1 1/2" Pipe)
thingiverse
Customized version of https://www.thingiverse.com/thing:2958009 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2958009
Corner fitting for metal-plastic pipe 1/2"
grabcad
Угловой фитинг под металлопластиковую трубу
1/2" PVC Corner
thingiverse
Corner piece for SCH40 PVC. ...This is a male fitting, which helps to minimize material usage.
Offset Corner Elbow for 1" PVC Pipe
thingiverse
Inspired by TonyYoungblood's [1/2" elbow](https://www.thingiverse.com/thing:533492), I created my version for larger diameter pipe and designed it to be tighter-fitting and use thinner glue. The tighter allowances mean that supports will...
1/2" pipe flange
thingiverse
This is a flange for 1/2 inch pipes with five 4mm holes. ... Diameter: 50mm
1/2" pipe saddle
thingiverse
This is a pipe saddle specifically for 1/2" pipe to mount it with a one hole strap to whatever you need to mount it to. ...
LICUATITTE PIPE 1-1/2"
grabcad
LICUATITTE PIPE 1-1/2"
1/2" Pipe Clamp
thingiverse
I made some shelves using 1/2 black pipe, npt flanges, and 1x12 pine board. I wanted a way to secure the shelf to pipe, so I made a clamp. These can also be used for 1/2" pipe clamps for plumbing purposes as well. Tolerances aren't super tight...
1/2" Pipe Clip
thingiverse
I needed 2 clips to keep my Mom's remote for her Pragmatic Adjustable Bed from sliding on the 1/2" pipe railing I built a few weeks ago. These did the trick. Please check out my video: https://youtu.be/ipaOke2cDNc This thing was made with...
1/2" Pipe Clip
pinshape
I needed 2 clips to keep my Mom's remote for her Pragmatic Adjustable Bed from sliding on the 1/2" pipe railing I built a few weeks ago. These did the trick. Please check out my video: https://youtu.be/ipaOke2cDNc This thing was made with...
1/2" Pipe Clamp
pinshape
Summary This clamp fits a standard 1/2" pvc pipe and will secure using an M4 16mm long and a nut. Probably a #6 would fit as well, but I haven't tried. As you can see, I'm using them to secure a couple of candelabra bulbs that I had left over from...
1/2" Pipe Clamp
thingiverse
This clamp fits a standard 1/2" pvc pipe and will secure using an M4 16mm long and a nut. Probably a #6 would fit as well, but I haven't tried. As you can see, I'm using them to secure a couple of candelabra bulbs that I had left over from removing...
Pipe union 1"-1/2"
grabcad
Муфта переходная 1" на 1/2"
1/2" NPT Pipe Fittings
thingiverse
Set of 1/2 NPT Pipe Fittings.
1/2 inch pipe mount
thingiverse
This is a mount to hold 1/2 inch copper pipe with one on each end. ...The diameter of the hole is slightly smaller than the actual pipe so you need to hammer the ends on.
1/2'' poly pipe stakes
thingiverse
For holding 1/2'' irrigation poly pipe string in place. Clips right onto pipe and helps keep the pipe in position, flat to the ground. Instructions Printed in PLA on low quality setting on the MB Replicator2 (.3mm layers, 10% fill, 2 shells). Great...
1/2 Inch Pipe (5" +)
myminifactory
Description: - Designed to fit print bed (110mm X 110mm X 110mm) - Minimal support needed - Meant to mimic Industrial Pipe (Black Iron Pipe) - Custom 45° angle Threads to reduce needed support Instructions: 1 (Top) 1 (Bottom) 1+ (MiddleShort...
1/2" PVC Pipe Support
thingiverse
... a 3d printer and I needed a rack to hold all of my filament spools. ...This thing is a bracket that mounts to the outside of a shelf or box and is designed to support a standard 1/2 inch pvc pipe. ...The mounting holes were designed for 3/16 bolts.
1/2" MIP Pipe Escutcheon
thingiverse
... the elbow fitting was protruding through the wall (pictured), The flange has a 7/16" recess to accommodate this. ... There are two versions included, a threaded version which fits 1/2" threaded pipe and an un-threaded version which fits fairly snugly.
1/2 inch pipe foot
myminifactory
foot for plastic pipe constructions!
Pipe Adaptor 2 into 1
grabcad
Pipe Adaptor drawn by Solidworks
Vesa Pipe Mount 1/2
thingiverse
The mount is for 1/2 z Pipe and M5 x35 screws. In the top part you need to insert 3*3 rubber bands or Print it with TPU included File. The rubber makes the mount super Stable and lowers the force you need to tighten it. The large hole for...
1/2" Copper Pipe Holder
thingiverse
Simple clip on mount for copper pipe. ...Designed it to fit a 1/4" tapcon because I'm using it in cinderblock but it should fit other screws well.
1/2" Pipe End Finial
thingiverse
Add some sweet flair to your home with a pipe curtain rod with a finial cap. ...
1/2" CPVC pipe connector
pinshape
This is a 3 way connector for .5" CPVC pipe. Tight fit with no glue needed for easy assembly and disassembly of projects.
1/2" Pipe Hanging Clips
thingiverse
One of my first projects and using Tinkercad...needed to install pipe plumbing to a new refrigerator to supply water for it...just made them. Thank you for looking. ...Enjoy!
1/2 Inch Pipe Connectors
thingiverse
... standers fitting. Just cut to length and slip with a little glue. Just note loadbearing capability will be better on one side depending on witch pipe fits in first because metal will be resting on metal. ... coupler and 4 way coming soon
Pipe clamp 1 1/2" 48-53mm
grabcad
This pipe clamp is copy to CADDY MACROFIX S M8 1 1/2" 48-53mm