Pipe Flange

pipe flange banner 3A flange, abbreviated as FLG, is a bolted connection where two pieces of pipe, equipment, fittings or valves are connected together to form a piping system.  Flanges provide access for when equipment (or piping) needs to be cleaned, inspected or reconfigured.   A flange pair is made up of two flanges and a gasket with bolts and nuts.  Pipe flanges come in different styles, pressure ratings, materials and sizes to meet the design requirements.  In the oil field, the two most commonly used flange standards are ANSI/ASME B16.5 and BS 1560. API Spec 6A is for flanges used on wellhead and christmas tree equipment.

Flanges of different standards or materials are not normally joined together.  There are instances where the design may require dissimilar metals or different classifications are required to be bolted together.  When this happens, be sure to seek engineering advise to ensure that the design is still within compliance with the applicable standards and specifications.

Abbreviations

  • FLG - flange
  • BF - blind flange
  • EXPF - expander flange
  • FBF - full barrel flange
  • FF -  flat face
  • HBF - heavy barrel flange
  • LJF - lap joint flange
  • LWNF - long weld neck flange
  • ORFF - orifice flange
  • OWNF - orifice weld neck flange
  • REDCF - reducing flange
  • RF - raised face
  • RTJ - ring type joint
  • RTJBF - ring type joint blind flange
  • RTJSOF - ring type joint slip-on flange
  • RTJTHRF - ring type joint threaded flange
  • RTJWNF - ring type joint weld neck flange
  • RTJF - ring type joint flange
  • SOF - slip-on flange
  • SWF - socket weld flange
  • TRHF - threaded flange
  • WNF - weld neck flange

 

Pipe flange Types

There are six basic types of flanges and are described by the way the connect to the piping system.  Click on the links below to be taken to a page detailing the different types of flanges.

Blind Flange (BF) 

These flanges do not have a bore. It is used to blind off a flange or even a valve.  When used at the end of a pipe or fitting, it provides an easy to open access for further extension of the pipe.  The blind flange and its bolts are stressed more than any other flange.

 

Lap Joint Flange (LJF) 

This flange is used with a lap joint stub end fitting.  It is similar to a slip-on flange, but with two differences.  The radius and the flat face, both allow the flange to secure against the stub end fitting.  This is useful where alignment of bolt holes is difficult, such as with spools to be attached to flanged nozzles of vessels.  A lap joint is used in low pressure applications and not suitable where high external of heavy loads are present.

 

Slip-on Flange (SOF)

Slip-on flanges are designed to slip over the outside of pipe, long-tangent elbows, reducers, and swages.  The flange has poor resistance to shock and vibration.  It is easier to align than a weld neck flange.  This flange is ideal for low pressure applications since the strength when under internal pressure is about one third that of a weld neck flange.

 

Socket Weld Flange (SWF)

This is similar to a slip-on flange, except they have a bored and counter bore.  The counter bore allows the pipe to fit into the socket/counter bore. The bore of the flange is the same diameter as the inside of the pipe.  These flanges were first designed for small diameter, high pressure pipe.

 

Threaded Flange (THDF)

It is similar to a slip-on Flange, but has internal threads.  It is normally used for low pressure and not used where temperature or stress is very high.

 

Weld Neck Flange (WNF)

This flange comes in two types, regular and long.  The hub of the weld neck is designed to reduce the stress at the base of the flange.  Regular weld neck flanges are used with buttweld fittings and long weld neck flanges are usually used with equipment and vessel nozzles.  A long weld neck flange is rarely used with pipe.  Both types of flanges are bored to match the inside diameter of the pipe or fitting to which it will be welded to.  They are suitable where high pressure, extreme temperatures, shear impact and vibratory stresses apply.

 

There are also a number of specialty flanges

Orifice Flange (ORFF)

Orifice flanges are for metering the volumetric flow rate of liquids and gasses through a pipe.  This flange is normally available in weld neck, slip-on, and threaded flanges.

Standard Connection Flange

This flange is normally used for nozzles on pressure vessels and rarely used with pipe.

Expander Flange (EXPF)

An expander flange is similar to a weld neck flange but with the hub expanding to a larger size (one or two sizes).

Reducing Flange (REDCF)

Reducing flanges are designed for when there is a change in the pipe size.

Studding Outlet Flange: Flat Bottom Mount - Shell/Head Mount - Tangential Mount

These flanges have shaped welded ends to match a tank or vessel.

Weldoflange / Nipoflange

A weldoflange is an olet connection, it is simular to a nipoflange, both are used for a branch connection on a pipe.

 

Pipe Flange Classes

Only the most used flange classes are listed on this page.  For more information on flanges and their respective standards, please follow the link below.

ASME B16.5 covers flanges with a nominal size from 1/2" through 24".  It also includes classes from ANSI 150 through ANSI 2500.  The flanges included in B16.5 are blind, lap joint, socket, slip-on, threaded and weld neck flanges.

ASME B16.47 covers flange with a nominal size of 24" and larger.  The flange classes it covers are from ANSI 75 through ANSI 900.  The flanges included are blind and weld neck flanges.  Additionally, B16.47 has two series of flanges, Series A (similar to ASME MSS SP44) & Series B (similar to API 605).  Series A flanges are larger, heavier and have fewer bolt holes.   The reason for series A and series B is that both specifications mentioned before were brought together to be covered under ASME B16.47.

 

Pipe Flange Facing

There are three primary types of flange facings.  Not all facings are available with each end connection.  This is based on the design of the flange and design of the piping system.  The typical flange facings are:

 

General Pipe Flange Standards

  • Flange - ASME B16.36, Orifice Flange (1/2"-24")
    • Slip-on Flange: Class 300, Class 400, Class 600, Class 900, Class 1500
    • Threaded Flange: Class 300, Class 400, Class 600, Class 900, Class 1500
    • Weld Neck Flange: Class 300, Class 400, Class 600, Class 900, Class 1500, Class 2500
  • Flange - Industry Standard Flange (also called Large Diameter Flange) (26"-larger)
    • Industry Standard Flanges have no national standard code or are they covered by any governing body.
      • Blind Flange: Class 75, Class 125, Class 175, Class 250, Class 350
      • Weld Neck Flange: Class 75, Class 125LW, Class 125, Class 175, Class 250, Class 350
      • Slip-on Flange: Class 75, Class 125LW, Class 125, Class 175, Class 250, Class 350
  • Flange - AWWA Standard Flange
    • AWWA C207
      • Steel Ring Flange: Class B, Class D, Class E, Class F
      • Steel Hub Flange: Class D, Class E
      • Blind Flange: Class B, Class D, Class E, Class F
    • AWWA C207
      • Steel Ring Flange: Class B, Class D, Class E, Class F
      • Steel Hub Flange: Class D, Class E
      • Blind Flange: Class B, Class D, Class E, Class F

 

Pipe Flange Pressure Classes

Flanges are normally manufactured in seven basic ratings: 150 Lb, 300 Lb, 400 Lb, 600 Lb, 900 Lb, 1500 Lb and 2500 Lb.  The ratings can be expressed in different ways but mean the same thing - 150 Lb, 150 Lbs, 150# or Class 150.

Each class of flange can handle more pressure than the previous class because of its construction.  The higher the class is, the thicker the metal is.  Thus a higher pressure can be handled.  There a numerous factors that can affect the pressure capability of a flange, such as the type of metal that is used.

 

Pipe Flange Specification, BSI

The BSI specifications for flanges are:

  • BS 10 - Specification for Flanges and Bolting for Pipes, Valves, and Fittings
  • BS 3293 - Specification for Carbon Steel Pipe Flanges (over 24 inches nominal size) for the Petroleum Industry
  • BS 4504 - Specification for Steel Flanges Circular Flanges for Pipes, Valves and Fittings
  • ISO 7005-1 - Metallic Flanges - Part 1: Steel Flanges (this is substantially the same as BS 4504)

BSI Flange Materials

Standards usually specify the material from which the flange is produced.

BSI Flange Sizes

There are available flange sizes and grades for all standard pipe wall thicknesses and pressure ratings.

BSI Flange Facing Types

The typical flange faces used are flat face, raised face, tongue and groove and ring joint.

BSI Flange Finish

The flange face finish is determined by the standard used and measured as an Arithmetical Average Roughness Height (AARH).  An example would be ANSI B16.5 which specifies face finishes within a range 125AARH - 500AARH (3.2 Ra to 12.5 Ra).

BSI Flange Class Rating

Flange

Type

BS4504

(ISO 7005-1)

DN 10 to

DN 4000

BS2393

26"-60"

Blind 2.5-40 -
Lap Joint 6-40 -
Slip-On 2.5-40 150-600
Socket - -
Threaded 6-40 -
Weld Neck 2.5-40 150-600
Flat/Raised Facing As Above As Above
Ring Joint Facing 2.5-40 300-600
Other Facings 2.5-40 -

 

Pipe Flange standards

ASME Standards

  • ASME B16.1 - Gray Iron Pipe Flanges and Flanged Fittings: Classes 25, 125, and 250
  • ASME B16.5 - Pipe Flanges and Flanged Fittings: NPS 1/2 through NPS 24 Metric/Inch Standard
  • ASME B16.24 - Cast Copper Alloy Pipe Flanges and Flanged Fittings: Classes 150, 300, 600, 900, 1500, and 2500
  • ASME B16.36 - Orifice Flanges
  • ASME B16.42 - Ductile Iron Pipe Flanges and Flanged Fittings: Classes 150 and 300
  • ASME B16.47 - Large Diameter Steel Flanges, NPS 26 Through NPS 60

ASTM Standards

  • ASTM A105 / A105M - Specification for Carbon Steel Forgings for Piping Applications

AWWA Standards

  • AWWA C115 - Standard for Flanged Ductile Iron Pipe with Ductile-Iron or Gray-Iron Threaded Flanges

ISO Standards

  • ISO 5251 - Stainless steel butt-welding fittings

MSS Standards

  • MSS SP-9 - Spot Facing for Bronze, Iron and Steel Flanges
  • MSS SP-25 - Standard Marking Systems for Valves, Fittings, Flanges, and Unions
  • MSS SP-44 - Steel Pipeline Flanges
  • MSS SP-106 - Cast Copper Alloy Flanges and Flanged Fittings Class 125,150, and 300
  • ASME B16.5 and ASME B16.47 cover pipe flanges up to NPS 60 (B16.5 from 1/2" to 24" and B16.47 from 26" to 60"). ANSI B16.47 covers two series of flanges, Series A is equal to MSS SP-44-44, and Series B is equal to API 605 (API 605 has been canclled).

 

Pipe Flange Datasheets

Pipe Flange Type Datasheets
Flanges All Flanges, ANSI (in)
Blind Blind Flange, ANSI (in)
Ductile Iron Ductile Iron Flange, ANSI (in)
Expander Expander Flange, ANSI (in)
Flange Bolt Flange Bolt, ANSI (in)
Lap Joint Lap Joint Flange, ANSI (in)
Orifice Orifice Flange, ANSI (in)
Slip-on Slip-on Flange, ANSI (in)
Socket Socket Flange, ANSI (in)
Standard Connection Standard Connection Flange, ANSI (in)
Studded Outlet Studded Outlet Flange, ANSI (in)
Threaded Threaded Flange, ANSI (in)
Weld Neck Weld Neck Flange, ANSI (in)

 

Pipe Flange Drawings

Looking for valve AutoCAD drawings?  We have them in our store.

 

Pipe Flange Related Articles

Display #
Title
Blind Flange
Bolt Circle
Bolt Tightening Procedure
Expander Flange
Flange Bolting Examples
Flange Facings, ASME B16.5
Flange Pressure and Temperature Ratings, B16.5
Flange Specification, BSI
Flange Stamping
Flange Welding Bevel Standard, ANSI B16.5 and B16.47
Flat Faced Flange
General Flange Standards
Lap Joint Flange
Orifice Flange
Orifice Plate
Raised Face Flange
Raised Face Smooth Finish
Reducing Flange
Ring Type Joint Flange
Slip-on Flange
Socket Weld Flange
Spectacle Blind
Standard Connection Flange
Threaded Flange
Weld Neck Flange

Tags: Flanges