One of the most commonly used type of flange in the process plant applications is the Raised Face flange 150 lbs. The Raised Face flange ansi b16. 5 is rather easily to identifiable. Raised Face Flange Manufacturers In India refer to it as a raised face because the surface of the gasket is raised above the bolting circle face. This face type allows the buyer to use a wide combination of gasket designs, including designs like flat ring sheet types and metallic composites such as spiral wound and double jacketed types with the duplex stainless steel Raised Face flange .
Table of Content
The purpose of a Pn16 Raised Face Flange is to concentrate more pressure on a smaller gasket area which in turn will increase the pressure containment capacity of the joint. Diameter and height of the carbon steel Raised Face flange in the ASME B16.5 definition are by pressure class and diameter. Pressure rating of the alloy steel Raised Face flange determines the height of the raised face.It is easy to recognize the Raised Face Flange Class 600 as the gasket surface area is positioned above the bolting line of the flange.
A Raised Face Flange Awwa C207 Class D is usually compatible with a wide range of flange gaskets. These gasket range could vary from flat to semi-metallic as well as metallic types. For instance, the gaskets for the Raised Face Flange A105 includes both jacketed gaskets as well as spiral wound gaskets, either in ring face or full face.The main scope of the Raised Face Flange Jis 10k design is so that the pressure of the two mating flanges is concentrated up on a small surface and increase the strength of the seal.
The height of the Raised Face Flange Jis 5k depends on the flange pressure rating. The pressure rating defined by the Raised Face Flange Asme B16.5 is meant for pressure ANSI classes 150 and 300, with the height of the Raised Face Flange Jis 16k being about 1.6 mm or 1/16 inch. And for ANSI classes that fall in between the range of class 400 to class 2500, the Api 6A Raised Face Flange height approximately reaches up to 6.4 mm, or 1/4 inch.
The most commonly used finish for the Raised Face Flange Din En 1092-1 is the 125 to 250 micron Ra (3 to 6 micron Ra). According to ASME B16.5, The raised face is the default flange face finish for manufacturers . this means that buyer must specify while placing the order with the Stainless Steel Raised Face Flange Manufacturer if another flange face is required. Or if it is required as a flat face or ring joint).
Raised Face Flange Asme B16.5 Class 300 are the most prominently type of flange seen in the applications of the petrochemical industry.
Raised Face Flanges type |
Raised Face Flanges Price in India |
Raised Face Flanges Price in USD |
Raised Face Flanges Price in UAE Dirham |
---|---|---|---|
Stainless Steel Raised Face Flanges |
INR 2876.42 / Kg |
USD $ 39.92 /Kg |
AED 147.98 UAE Dirham |
Carbon steel Raised Face Flanges |
INR 2140.05 / Kg |
USD $ 28.82 /Kg |
AED 100.88 UAE Dirham |
Alloy steel Raised Face Flanges |
INR 2842.42 / Kg |
USD $ 38.92 /Kg |
AED 130.98 UAE Dirham |
ANSI b16 5 Raised Face Flanges |
INR 2500.83 / Kg |
USD $ 30.74 /Kg |
AED 110.95 UAE Dirham |
ASME b16.47 Raised Face Flanges |
INR 2602.86 / Kg |
USD $ 28.12 /Kg |
AED 120.02 UAE Dirham |
Raised Face (RF) Flange seal with a flat gasket, formerly made of asbestos but now made of more environmentally friendly material, designed for installation between the raised faces of two mating flanges (both with raised faces). It is referred to as a raised face because the gasket surfaces are raised above the bolting circle face. The purpose of a RF flange is to concentrate more pressure on a smaller gasket area and thereby increase the pressure containment capability of the joint.
Raised Face Flanges Standards | ANSI/ASME B16.5, B16.47 Series A & B, B16.48, BS4504, BS 10, EN-1092, DIN, ANSI Flanges, ASME Flanges, BS Flanges, DIN Flanges, EN Flanges, GOST Flange, ASME/ANSI B16.5/16.36/16.47A/16.47B, MSS S44, ISO70051, JISB2220, BS1560-3.1, API7S-15, API7S-43, API605, EN1092 |
---|---|
ASME B16.5 Raised Face Flanges Size Chart | 1/2" (15 NB) to 48" (1200NB) DN10~DN5000 |
Raised Face Flanges Pressure Calculation in DIN | 6Bar 10Bar 16Bar 25Bar 40Bar / PN6 PN10 PN16 PN25 PN40, PN64 Raised Face Flanges |
Raised Face Flanges Pressure Rating ANSI | Class 150 LBS, 300 LBS, 600 LBS, 900 LBS, 1500 LBS, 2500 LBS Raised Face Flanges |
UNI | 6Bar 10Bar 16Bar 25Bar 40Bar Raised Face Flanges |
JIS | 5K, 10 K, 16 K 20 K, 30 K, 40 K, 63 K Raised Face Flanges |
Coating | Oil Black Paint, Anti-rust Paint, Zinc Plated, Yellow Transparent, Cold and Hot Dip Galvanized Raised Face Flanges |
EN | 6Bar 10Bar 16Bar 25Bar 40Bar Raised Face Flanges |
Test Certificates | EN 10204/3.1B Raw Materials Certificate 100% Radiography Test Report Third Party Inspection Report, etc |
Most common types of Raised Face Flanges | Forged / Threaded / Screwed / Plate |
Connect Type/ Flange Face Type | Raised Face (RF), Ring Type Joint (RTJ), Flat Face (FF), Large Male-Female (LMF), Lap-Joint Face (LJF), Small Male-Female (SMF), Small Tongue, Large Tongue & Groove, Groove |
Production technique |
|
Test | Direct-reading Spectrograph, Hydrostatic testing machine, X-ray detector, UI trasonic flaw detector, Magnetic particle detector |
Special design |
As per your drawing AS, ANSI, BS, DIN and JIS |
Origin | Indian / West Europe / Japan / USA / Korean |
Equipment | Press machine, Bending machine, Pushing Machine, electric bevelling machine, Sand-blasting machine etc |
Raised Face Flanges Uses & application |
|
Manufacturer of |
ANSI DIN, GOST, JIS, UNI, BS, AS2129, AWWA, EN, SABS, NFE etc.
|
Export to | Saudi Arabia, Peru, Egypt, Indonesia, Brazil, Spain, USA, Canada, Ukraine, Singapore, Thailand, Oman, Ireland, Korea, Iran, India, Dubai |
Material Test Certificates (MTC) as per EN 10204 3.1 and EN 10204 3.2, Test Certificates certifying NACE MR0103, NACE MR0175 |
Flanges pressure rating in psig for Ring Type Joint Flange ASME |
|||||||
Temperature (F°) |
150# |
300# |
400# |
600# |
900# |
1500# |
2500# |
-20 to 100 |
285 |
740 |
985 |
1480 |
2220 |
3705 |
6170 |
200 |
260 |
680 |
905 |
1360 |
2035 |
3395 |
5655 |
300 |
230 |
655 |
870 |
1310 |
1965 |
3270 |
5450 |
400 |
200 |
635 |
845 |
1265 |
1900 |
3170 |
5280 |
500 |
170 |
605 |
805 |
1205 |
1810 |
3015 |
5025 |
600 |
140 |
570 |
755 |
1135 |
1705 |
2840 |
4730 |
650 |
125 |
550 |
730 |
1100 |
1650 |
2745 |
4575 |
700 |
110 |
530 |
710 |
1060 |
1590 |
2655 |
4425 |
750 |
95 |
505 |
675 |
1015 |
1520 |
2535 |
4230 |
800 |
80 |
410 |
550 |
825 |
1235 |
2055 |
3430 |
850 |
65 |
320 |
425 |
640 |
955 |
1595 |
2655 |
900 |
50 |
230 |
305 |
460 |
690 |
1150 |
1915 |
950 |
35 |
135 |
185 |
275 |
410 |
685 |
1145 |
1000 |
20 |
85 |
115 |
170 |
255 |
430 |
715 |
Nominal Pipe Size NPS (inches) |
Class 150 |
||||
---|---|---|---|---|---|
Diameter of Flange (inches) |
No. of Bolts |
Diameter of Bolts (inches) |
Diameter of Bolt Holes (inches) |
Bolt Circle (inches) |
|
1/4 |
3-3/8 |
4 |
1/2 |
0.62 |
2-1/4 |
1/2 |
3-1/2 |
4 |
1/2 |
0.62 |
2-3/8 |
3/4 |
3-7/8 |
4 |
1/2 |
0.62 |
2-3/4 |
1 |
4-1/4 |
4 |
1/2 |
0.62 |
3-1/8 |
1-1/4 |
4-5/8 |
4 |
1/2 |
0.62 |
3-1/2 |
1-1/2 |
5 |
4 |
1/2 |
0.62 |
3-7/8 |
2 |
6 |
4 |
5/8 |
0.75 |
4-3/4 |
2-1/2 |
7 |
4 |
5/8 |
0.75 |
5-1/2 |
3 |
7-1/2 |
4 |
5/8 |
0.75 |
6 |
3-1/2 |
8-1/2 |
8 |
5/8 |
0.75 |
7 |
4 |
9 |
8 |
5/8 |
0.75 |
7-1/2 |
5 |
10 |
8 |
3/4 |
0.88 |
8-1/2 |
6 |
11 |
8 |
3/4 |
0.88 |
9-1/2 |
8 |
13-1/2 |
8 |
3/4 |
0.88 |
11-3/4 |
10 |
16 |
12 |
7/8 |
1 |
14-1/4 |
12 |
19 |
12 |
7/8 |
1 |
17 |
14 |
21 |
12 |
1 |
1.12 |
18-3/4 |
16 |
23-1/2 |
16 |
1 |
1.12 |
21-1/4 |
18 |
25 |
16 |
1-1/8 |
1.25 |
22-3/4 |
20 |
27-1/2 |
20 |
1-1/8 |
1.25 |
25 |
24 |
32 |
20 |
1-1/4 |
1.38 |
29-1/2 |
Nominal Pipe Size NPS (inches) |
Class 300 |
||||
---|---|---|---|---|---|
Diameter of Flange (inches) |
No. of Bolts |
Diameter of Bolts (inches) |
Diameter of Bolt Holes (inches) |
Bolt Circle (inches) |
|
1/4 |
3-3/8 |
4 |
1/2 |
0.62 |
2-1/4 |
1/2 |
3-3/4 |
4 |
1/2 |
0.62 |
2-5/8 |
3/4 |
4-5/8 |
4 |
5/8 |
0.75 |
3-1/4 |
1 |
4-7/8 |
4 |
5/8 |
0.75 |
3-1/2 |
1-1/4 |
5-1/4 |
4 |
5/8 |
0.75 |
3-7/8 |
1-1/2 |
6-1/8 |
4 |
3/4 |
0.88 |
4-1/2 |
2 |
6-1/2 |
8 |
5/8 |
0.75 |
5 |
2-1/2 |
7-1/2 |
8 |
3/4 |
0.88 |
5-7/8 |
3 |
8-1/4 |
8 |
3/4 |
0.88 |
6-5/8 |
3-1/2 |
9 |
8 |
3/4 |
0.88 |
7-1/4 |
4 |
10 |
8 |
3/4 |
0.88 |
7-7/8 |
5 |
11 |
8 |
3/4 |
0.88 |
9-1/4 |
6 |
12-1/2 |
12 |
3/4 |
0.88 |
10-5/8 |
8 |
15 |
12 |
7/8 |
1 |
13 |
10 |
17-1/2 |
16 |
1 |
1.12 |
15-1/4 |
12 |
20-1/2 |
16 |
1-1/8 |
1.25 |
17-3/4 |
14 |
23 |
20 |
1-1/8 |
1.25 |
20-1/4 |
16 |
25-1/2 |
20 |
1-1/4 |
1.38 |
22-1/2 |
18 |
28 |
24 |
1-1/4 |
1.38 |
24-3/4 |
20 |
30-1/2 |
24 |
1-1/4 |
1.38 |
27 |
24 |
36 |
24 |
1-1/2 |
1.62 |
32 |
Nominal Pipe Size NPS (inches) |
Class 400 |
||||
---|---|---|---|---|---|
Diameter of Flange (inches) |
No. of Bolts |
Diameter of Bolts (inches) |
Diameter of Bolt Holes (inches) |
Bolt Circle (inches) |
|
1/4 |
3-3/8 |
4 |
1/2 |
0.62 |
2-1/4 |
1/2 |
3-3/4 |
4 |
1/2 |
0.62 |
2-5/8 |
3/4 |
4-5/8 |
4 |
5/8 |
0.75 |
3-1/4 |
1 |
4-7/8 |
4 |
5/8 |
0.75 |
3-1/2 |
1-1/4 |
5-1/4 |
4 |
5/8 |
0.75 |
3-7/8 |
1-1/2 |
6-1/8 |
4 |
3/4 |
0.88 |
4-1/2 |
2 |
6-1/2 |
8 |
5/8 |
0.75 |
5 |
2-1/2 |
7-1/2 |
8 |
3/4 |
0.88 |
5-7/8 |
3 |
8-1/4 |
8 |
3/4 |
0.88 |
6-5/8 |
3-1/2 |
9 |
8 |
7/8 |
1 |
7-1/4 |
4 |
10 |
8 |
7/8 |
1 |
7-7/8 |
5 |
11 |
8 |
7/8 |
1 |
9-1/4 |
6 |
12-1/2 |
12 |
7/8 |
1 |
10-5/8 |
8 |
15 |
12 |
1 |
1.12 |
13 |
10 |
17-1/2 |
16 |
1-1/8 |
1.25 |
15-1/4 |
12 |
20-1/2 |
16 |
1-1/4 |
1.38 |
17-3/4 |
14 |
23 |
20 |
1-1/4 |
1.38 |
20-1/4 |
16 |
25-1/2 |
20 |
1-3/8 |
1.5 |
22-1/2 |
18 |
28 |
24 |
1-3/8 |
1.5 |
24-3/4 |
20 |
30-1/2 |
24 |
1-1/2 |
1.62 |
27 |
24 |
36 |
24 |
1-3/4 |
1.88 |
32 |
Nominal Pipe Size NPS (inches) |
Class 600 |
||||
---|---|---|---|---|---|
Diameter of Flange (inches) |
No. of Bolts |
Diameter of Bolts (inches) |
Diameter of Bolt Holes (inches) |
Bolt Circle (inches) |
|
1/4 |
3-3/8 |
4 |
1/2 |
0.62 |
2-1/4 |
1/2 |
3-3/4 |
4 |
1/2 |
0.62 |
2-5/8 |
3/4 |
4-5/8 |
4 |
5/8 |
0.75 |
3-1/4 |
1 |
4-7/8 |
4 |
5/8 |
0.75 |
3-1/2 |
1-1/4 |
5-1/4 |
4 |
5/8 |
0.75 |
3-7/8 |
1-1/2 |
6-1/8 |
4 |
3/4 |
0.88 |
4-1/2 |
2 |
6-1/2 |
8 |
5/8 |
0.75 |
5 |
2-1/2 |
7-1/2 |
8 |
3/4 |
0.88 |
5-7/8 |
3 |
8-1/4 |
8 |
3/4 |
0.88 |
6-5/8 |
3-1/2 |
9 |
8 |
7/8 |
1 |
7-1/4 |
4 |
10-3/4 |
8 |
7/8 |
1 |
8-1/2 |
5 |
13 |
8 |
1 |
1.12 |
10-1/2 |
6 |
14 |
12 |
1 |
1.12 |
11-1/2 |
8 |
16-1/2 |
12 |
1-1/8 |
1.25 |
13-3/4 |
10 |
20 |
16 |
1-1/4 |
1.38 |
17 |
12 |
22 |
20 |
1-1/4 |
1.38 |
19-1/4 |
14 |
23-3/4 |
20 |
1-3/8 |
1.5 |
20-3/4 |
16 |
27 |
20 |
1-1/2 |
1.62 |
23-3/4 |
18 |
29-1/4 |
20 |
1-5/8 |
1.75 |
25-3/4 |
20 |
32 |
24 |
1-5/8 |
1.75 |
28-1/2 |
24 |
37 |
24 |
1-7/8 |
2 |
33 |
Nominal Pipe Size NPS (inches) |
Class 900 |
||||
---|---|---|---|---|---|
Diameter of Flange (inches) |
No. of Bolts |
Diameter of Bolts (inches) |
Diameter of Bolt Holes (inches) |
Bolt Circle (inches) |
|
1/2 |
4-3/4 |
4 |
3/4 |
0.88 |
3-1/4 |
3/4 |
5-1/8 |
4 |
3/4 |
0.88 |
3-1/2 |
1 |
5-7/8 |
4 |
7/8 |
1 |
4 |
1-1/4 |
6-1/4 |
4 |
7/8 |
1 |
4-3/8 |
1-1/2 |
7 |
4 |
1 |
1.12 |
4-7/8 |
2 |
8-1/2 |
8 |
7/8 |
1 |
6-1/2 |
2-1/2 |
9-5/8 |
8 |
1 |
1.12 |
7-1/2 |
3 |
9-1/2 |
8 |
7/8 |
1 |
7-1/2 |
4 |
11-1/2 |
8 |
1-1/8 |
1.25 |
9-1/4 |
5 |
13-3/4 |
8 |
1-1/4 |
1.38 |
11 |
6 |
15 |
12 |
1-1/8 |
1.25 |
12-1/2 |
8 |
18-1/2 |
12 |
1-3/8 |
1.5 |
15-1/2 |
10 |
21-1/2 |
16 |
1-3/8 |
1.5 |
18-1/2 |
12 |
24 |
20 |
1-3/8 |
1.5 |
21 |
14 |
25-1/4 |
20 |
1-1/2 |
1.62 |
22 |
16 |
27-3/4 |
20 |
1-5/8 |
1.75 |
24-1/2 |
18 |
31 |
20 |
1-7/8 |
2 |
27 |
20 |
33-3/4 |
20 |
2 |
2.12 |
29-1/2 |
24 |
41 |
20 |
2-1/2 |
2.62 |
35-1/2 |
Nominal Pipe Size NPS (inches) |
Class 1500 |
||||
---|---|---|---|---|---|
Diameter of Flange (inches) |
No. of Bolts |
Diameter of Bolts (inches) |
Diameter of Bolt Holes (inches) |
Bolt Circle (inches) |
|
1/2 |
4-3/4 |
4 |
3/4 |
0.88 |
3-1/4 |
3/4 |
5-1/8 |
4 |
3/4 |
0.88 |
3-1/2 |
1 |
5-7/8 |
4 |
7/8 |
1 |
4 |
1-1/4 |
6-1/4 |
4 |
7/8 |
1 |
4-3/8 |
1-1/2 |
7 |
4 |
1 |
1.12 |
4-7/8 |
2 |
8-1/2 |
8 |
7/8 |
1 |
6-1/2 |
2-1/2 |
9-5/8 |
8 |
1 |
1.12 |
7-1/2 |
3 |
10-1/2 |
8 |
1-1/8 |
1.25 |
8 |
4 |
12-1/4 |
8 |
1-1/4 |
1.38 |
9-1/2 |
5 |
14-3/4 |
8 |
1-1/2 |
1.62 |
11-1/2 |
6 |
15-1/2 |
12 |
1-3/8 |
1.5 |
12-1/2 |
8 |
19 |
12 |
1-5/8 |
1.75 |
15-1/2 |
10 |
23 |
12 |
1-7/8 |
2 |
19 |
12 |
26-1/2 |
16 |
2 |
2.12 |
22-1/2 |
14 |
29-1/2 |
16 |
2-1/4 |
2.38 |
25 |
16 |
32-1/2 |
16 |
2-1/2 |
2.62 |
27-3/4 |
18 |
36 |
16 |
2-3/4 |
2.88 |
30-1/2 |
20 |
38-3/4 |
16 |
3 |
3.12 |
32-3/4 |
24 |
46 |
16 |
3-1/2 |
3.62 |
39 |
Nominal Pipe Size NPS (inches) |
Class 2500 |
||||
---|---|---|---|---|---|
Diameter of Flange (inches) |
No. of Bolts |
Diameter of Bolts (inches) |
Diameter of Bolt Holes (inches) |
Bolt Circle (inches) |
|
1/2 |
5-1/4 |
4 |
3/4 |
0.88 |
3-1/2 |
3/4 |
5-1/2 |
4 |
3/4 |
0.88 |
3-3/4 |
1 |
6-1/4 |
4 |
7/8 |
1 |
4-1/4 |
1-1/4 |
7-1/4 |
4 |
1 |
1.12 |
5-1/8 |
1-1/2 |
8 |
4 |
1-1/8 |
1.25 |
5-3/4 |
2 |
9-1/4 |
8 |
1 |
1.12 |
6-3/4 |
2-1/2 |
10-1/2 |
8 |
1-1/8 |
1.25 |
7-3/4 |
3 |
12 |
8 |
1-1/4 |
1.38 |
9 |
4 |
14 |
8 |
1-1/2 |
1.62 |
10-3/4 |
5 |
16-1/2 |
8 |
1-3/4 |
1.88 |
12-3/4 |
6 |
19 |
8 |
2 |
2.12 |
14-1/2 |
8 |
21-3/4 |
12 |
2 |
2.12 |
17-1/4 |
10 |
26-1/2 |
12 |
2-1/2 |
2.62 |
21-1/4 |
12 |
30 |
12 |
2-3/4 |
2.88 |
24-3/8 |
Galavnized Raised Face Flanges |
DIN Raised Face Pipe Flanges |
Stainless Steel Raised Face Flanges |
Raised Face Steel Flanges |
Slip On Raised Face Flanges |
High Quality Raised Face Flanges |
Flange Raised Face |
Table E Raised Face Flanges |
ANSI B16.5 class 150 Raised Face Flange |
PN16 Raised Face Flanges |
2 inch Raised Face Flanges |
ANSI 150 Raised Face Flange |
Carbon Steel Raised Face Flange |
ANSI B16.5 Class 150 Raised Face Flanges |
Raised Face Flange |
ANSI Raised Face Flange |
Weld Neck Raised Face Flange |
Raised Face Flange Dimensions |
ASME B16.5 Raised Face Flanges |
4 inch Raised Face Flanges |
ANSI B16.5 Raised Face Flanges |
SS Raised Face Flange |
|
|
Raised Face Flanges Class 900 |
Raised Face Flanges Flat Face |
Raised Face Flanges Pn16 |
Kf Raised Face Flanges |
Raised Face Flanges Class 2500 |
Raised Face Flanges Slip On |
Raised Face Flanges Din 2527 |
Raised Face Flanges Weight 150# |
Raised Face Flanges Din 2576 |
Raised Face Flanges With 1/2 Npt
|
Raised Face Flanges Pn 64 |
Raised Face Flanges Ansi B16.5 150 |
Raised Face Flanges Class 150 |
Raised Face Flanges Threaded |
Raised Face Flanges Pn10 |
Raised Face Flanges B16.47 |
Raised Face Flanges Pn40 |
Raised Face Flanges Rtj 900 |
Raised Face Flanges Pn 160 |
Raised Face Flanges Rtj |
Raised Face Flanges Class 1500 |
Raised Face Flanges Npt |
Raised Face Flanges Dn150 Pn16 |
Raised Face Flanges Jis 5k |
Raised Face Flanges Class 600 |
Raised Face Flanges Jis B2220 |
Raised Face Flanges Asme B16.5 Class 300 |
Raised Face Flanges Ring Type Joint |
Raised Face Flanges Din 2633 |
Raised Face Flanges Rtj 1500 |
Raised Face Flanges Class 300 |
Raised Face Flanges With Threaded Hole |
Raised Face Flanges Din En 1092-1 |
Raised Face Flanges Jis 10k |
Stainless Steel Raised Face Flanges | ASTM/ASME A/SA182 F304, F304L, F316, F316L, ASTM/ASME A/SA351 CF8, CF3, CF8M, CF3M, DIN 1.4301, DIN 1.4306, DIN 1.4401, DIN 1.4404, DIN 1.4308, DIN 1.4408, DIN 1.4306, DIN 1.4409 |
Carbon Steel Raised Face Flanges | ASTM/ASME A/SA105 A/SA105N & A/SA216-WCB, DIN 1.0402, DIN 1.0460, DIN 1.0619, Die Steel, ASTM A105 / ASME SA105, A105N, ASTM A350 LF2 / ASME SA350, High Yield CS ASTM A694 / A694 (F52 F56 F60 F65 F70 F80) |
Titanium Raised Face Flanges | ASTM B381 / ASME SB381, Titanium Gr. 1, Titanium Gr. 2, Titanium Gr. 4, Titanium Gr. 5, Titanium Gr. 7 ASTM R50250/GR.1 | R50400/GR.2 | R50550/GR.3 | R50700/GR.4 | GR.6 |R52400/GR.7 | R53400/GR.12 | R56320/GR.9 |R56400/GR.5 |
Alloy Steel Raised Face Flanges | ASTM A182 / ASME SA182 F5, F9, F11, F12, F22, F91 |
Copper Nickel Raised Face Flanges | ASTM / ASME SB 61 / 62 / 151 / 152, Copper Nickel 90/10 (C70600 ), Cupro Nickel 70/30 (C71500), UNS C71640 |
Copper Raised Face Flanges | T1, T2, C10100, C10200, C10300, C10400, C10500, C10700, C10800, C10910,C10920, TP1, TP2, C10930, C11000, C11300, C11400, C11500, C11600, C12000,C12200, C12300, TU1, TU2, C12500, C14200, C14420, C14500, C14510, C14520, C14530, C17200, C19200, C21000, C23000, C26000, C27000, C27400, C28000, C33000, C33200, C37000, C44300, C44400, C44500, C60800, C63020, C68700, C70400, C70600, C70620, C71000, C71500, C71520, C71640, etc |
Inconel Raised Face Flanges | ASTM B564 / ASME SB564, Inconel 600, 601, 625, 718, 783, 690, x750 Raised Face Flanges |
Brass Raised Face Flanges | 3602 / 2604 / H59 / H62 / etc. |
Monel Raised Face Flanges | ASTM B564 / ASME SB564, Monel 400 (UNS No. N04400), Monel 500 (UNS No. N05500) |
Hastelloy Raised Face Flanges | ASTM B564 / ASME SB564, Hastelloy C276 (UNS N10276), C22 (UNS N06022), C4, C2000, B2, B3, X Flanges |
Aluminium Raised Face Flanges | 5052 /6061/ 6063 / 2017 / 7075 / etc. |
Alloy 20 Raised Face Flanges | ASTM B462 / ASME SB462, Carpenter® 20 Alloy, Alloy 20Cb-3 |
Duplex Raised Face Flanges | S31803 / S32205 A182 Gr F51 / F52 / F53 / F54 / F55 / F57 / F59 / F60 / F61 |
Nickel Raised Face Flanges | ASTM B564 / ASME SB564, Nickel 200, Nickel 201, Nickel 205, Nickel 205LC |
Incoloy Raised Face Flanges | ASTM B564 / ASME SB564, Incoloy 800, 800H, 800HT (UNS N08800), 825 (UNS N08825), 925 Flanges |
Super Duplex Raised Face Flanges | S32750 / S32760 A182 Gr F51 / F52 / F53 / F54 / F55 / F57 / F59 / F60 / F61 |
Other Raised Face Flanges material | Tin bronze, Alumunum bronze, Lead bronze |
Nimonic Raised Face Flanges | Nimonic 75, Nimonic 80A, Nimonic 90 |
254 Smo Raised Face Flanges | ASTM A182 / ASME SA182, SMO 254/6Mo, UNS S31254, DIN 1.4547 |
|
|